Serving Glendale, Burbank and Greater Los Angeles
Free Quotes (424) 653-0453
Camberos Masonry Brick · Block · Stone · Concrete
New concrete steps with lights set into the risers on a sloped Los Angeles yard
Call (424) 653-0453 Get a Free Quote

How much does a walkway cost in Los Angeles?

National cost guides put a poured concrete walkway at about $8 to $12 per square foot. Pavers run $9 to $20 in LawnStarter’s 2026 guide, and HomeGuide puts brick at $15 to $30+. Flagstone starts higher, at $29.53 to $37.75 per square foot in Homewyse’s May 2026 estimate. Poured concrete steps add $200 to $500 per step, HomeGuide says.

These are national figures. A Los Angeles price comes from measuring your walk on site, along with its slope and any old concrete. Tear-out, the base, steps and a parkway permit can all add to the total.

What does each kind of walkway cost?

Each guide prices its own way, so every row names its source. All figures are national. The last two columns use a front walk 4 feet wide and 50 feet long.

Walkway surfaceNational range per square footA 4 by 50 foot front walk (200 sq ft)What drives it
Poured concreteAbout $8 to $12 (HomeAdvisor)$1,600 to $2,400, average $2,000Tear-out and joints
Pavers$9 to $20 (LawnStarter, 2026)$1,800 to $4,000Base depth and edge restraint
Brick$15 to $30+ (HomeGuide)$3,000 to $6,000 or morePattern and cuts
FlagstoneStarts at $29.53 to $37.75 (Homewyse, May 2026)Starts at $5,906 to $7,550Sand bed or concrete base

Steps are priced by the step or by the run. These are national guide figures too:

  • Poured concrete steps: $200 to $500 per step, or $1,000 to $5,000 for 5 to 10 steps (HomeGuide)
  • Precast concrete steps: $100 to $350 per step installed (HomeGuide)
  • Stone steps: $1,500 to $9,000 installed (HomeGuide)
  • Custom poured-in-place staircases: $1,800 to $6,000 (HomeAdvisor)

The number of steps comes from how much the ground drops. Step heights follow code rules, set out on our page for walks and entry steps we build.

For pavers, LawnStarter’s 2026 guide puts a typical project at $1,430 to $3,530. Its national average is $2,480.

Why does brick cost more than concrete?

Brick is laid one unit at a time. HomeGuide says professional installation accounts for at least half of a brick walk’s total cost. Busy patterns push it higher. HomeGuide names herringbone and basketweave as patterns that add labor time and material waste.

We have laid a clay brick walkway in a herringbone pattern between planting beds. Brick also works as an inlay. A Google customer picked us from a few bids to add a front walkway with a brick inlay. The review credits our fair pricing and our communication from the start.

A brick walk is set in sand or in mortar, much like a patio. Both methods are covered under clay brick paving in sand or mortar.

What does tearing out an old walk add?

HomeAdvisor prices concrete removal at $2 to $6 per square foot. On a 200 square foot walk, that adds $400 to $1,200 before any new work starts. Old concrete steps cost $200 to $400 to remove, in HomeAdvisor’s figures.

Repair can come first. HomeGuide puts concrete step repair at $300 to $800 on average, which usually covers patching cracks or small sections. An old stone path can sometimes be repaired instead of replaced. One Yelp customer had us repair mortar joints and cracks in natural stone pathways at a circa 1930 property.

Why does the base change the price?

The base is the part of a walkway you pay for and never see. City of LA plan check treats local soil as expansive unless a soils report says otherwise.

A paver walk is built in layers. Paver guidance calls for 4 to 6 inches of compacted aggregate base under a walk. On top goes 1 to 1.5 inches of bedding sand. Edge restraint holds the sides in line. Our page on paver walks laid over a compacted base shows the build.

Flagstone comes two ways. Dry laid stone sits on a bed of sand and gravel. Mortared flagstone starts with a reinforced concrete base, so you pay for a pour before the stone goes down. Both are covered under flagstone set dry or on a concrete slab.

A concrete walk needs planned joints. NRMCA, the ready mixed concrete industry group, spaces them at 24 to 36 times the slab thickness. On a 4 inch slab, that lands near 10 feet.

How do steps change the cost of a walkway?

HomeAdvisor’s range for concrete step installation runs from $400 to $6,000. Precast steps cost less than a custom pour, at about $600 to $2,000.

Steps can be built in the same material as the walk. Our finished work includes clay brick front steps beside an old river rock wall. We have also set flagstone entry steps between stucco pilasters.

Lights add their own line. We have poured a new concrete stair run on a slope with lights blocked into the risers. HomeGuide puts hardwired low-voltage path lights at $50 to $150 per light installed. The wiring is done by a licensed electrician.

Do you need a permit for a walkway in Los Angeles?

On your own lot in the City of Los Angeles, usually not. LAMC 91.106.2 exempts walks not more than 30 inches above grade from a building permit. The walk also cannot sit over a basement or a story below. Our post on the 30 inch rule for flatwork permits covers the details.

The parkway is different. The parkway strip and the sidewalk are public right of way. LAMC 62.105 requires a Bureau of Engineering permit for construction there, called an A-Permit.

The A-Permit basic fee is $336 for permits issued on or after July 1, 2026. A 7 percent surcharge and a 3 percent surcharge are added to the listed fee, each with a $1 minimum. Inspection for concrete sidewalk work is $0.85 per square foot, with a 10 square foot minimum of $8.50. Our guide to how a parkway A-Permit works goes step by step.

The city’s sidewalk standard calls for at least 3 inches of concrete, sloped up from the curb at 2 percent. That is about a quarter inch per foot. Glendale, Burbank and Pasadena run their own permits, so each city sets its own rules there.

How a walkway quote comes together

A quote starts on site. We measure the walk and count the steps. We also look at the slope and any old concrete. The written quote then lists the tear-out, the base, the surface and the steps.

If your new walk crosses the parkway, the permit is handled as part of the job. The paperwork is filed for you where the agency allows it. Your walkway quote is free and in writing, and we give it on site.

Frequently asked questions

How much does a concrete walkway cost?
A poured concrete walkway runs about $8 to $12 per square foot in HomeAdvisor's national figures. Its standard 200 square foot walk costs $1,600 to $2,400 installed, with an average of $2,000. Tearing out an old walk adds $2 to $6 per square foot. A Los Angeles price comes from measuring your walk on site.
How much does a paver walkway cost?
A paver walkway costs $9 to $20 per square foot, LawnStarter's 2026 guide says. Most projects in that national guide land between $1,430 and $3,530, with an average of $2,480. The base is part of that price. Paver guidance calls for 4 to 6 inches of compacted aggregate base under a walk. Then comes 1 to 1.5 inches of bedding sand.
How much does a flagstone walkway cost?
Homewyse's May 2026 estimate for a flagstone walkway starts at $29.53 to $37.75 per square foot. Even its low end sits above the top of the national concrete and paver ranges. Dry laid flagstone rests on a bed of sand and gravel. Mortared flagstone starts with a reinforced concrete base, so that job includes a pour.
How much does a brick walkway cost?
HomeGuide puts a brick walkway at $15 to $30+ per square foot. A walk 20 feet long and wide enough for two people side by side runs $1,500 to $3,000. Labor makes up at least half of the total, HomeGuide says. Herringbone or basketweave patterns take more labor and waste more brick.
How much do concrete steps cost?
Poured concrete steps cost $200 to $500 per step, HomeGuide says. A run of 5 to 10 steps costs $1,000 to $5,000. Precast steps run $100 to $350 per step installed. HomeAdvisor puts custom poured-in-place staircases at $1,800 to $6,000. HomeGuide's average for repairing a cracked step is $300 to $800.
Do I need a permit for a walkway in Los Angeles?
Not for most walks on your own lot in the City of Los Angeles. LAMC 91.106.2 exempts walks not more than 30 inches above grade. The walk cannot sit over a basement or a story below. The parkway strip out to the curb is public right of way, though. Work there takes a Bureau of Engineering permit.
Start Your Project

Get In Touch With Camberos Masonry

A wall that worries you, a driveway past its best, or a backyard ready to become the good part of the house? Call or send the form and we will look at the site with you and hand you a straight written quote.

Get a Free Quote

Tell us about your project - we’ll get right back to you.

Call (424) 653-0453